Complementary
specific application
HVAC
Accuracy
+/- 0.6 % (VIA) for a temperature variation 60 °C
+/- 0.6 % (VIB) for a temperature variation 60 °C
+/- 1 % (FM) for a temperature variation 60 °C
maximum switching current
5 A at 250 V AC on resistive load - cos phi = 1 - L/R = 0 ms (FL, R)
5 A at 30 V DC on resistive load - cos phi = 1 - L/R = 0 ms (FL, R)
2 A at 250 V AC on inductive load - cos phi = 0.4 - L/R = 7 ms (FL, R)
2 A at 30 V DC on inductive load - cos phi = 0.4 - L/R = 7 ms (FL, R)
Product certifications
C-Tick
UL
NOM 117
CSA
response time
FM 2 ms, tolerance +/- 0.5 ms for analog output(s)
FLA, FLC 7 ms, tolerance +/- 0.5 ms for discrete output(s)
FLB, FLC 7 ms, tolerance +/- 0.5 ms for discrete output(s)
RY, RC 7 ms, tolerance +/- 0.5 ms for discrete output(s)
data formats
8 bits, 1 stop, odd even or no configurable parity
Handle front plate colour
340 mm
Product or component type
Variable speed drive
tightening torque
1.3 N.m, 11.5 lb.in (L1/R, L2/S, L3/T)
0.6 N.m (VIA, VIB, FM, FLA, FLB, FLC, RY, RC, F, R, RES)
[us] rated supply voltage
380...480 V - 15...10 %
Assembly style
With heat sink
minimum switching current
3 mA at 24 V DC for configurable relay logic
noise level
55 dB conforming to 86/188/EEC
marking
CE
Analogue input number
2
Analogue input type
VIA switch-configurable voltage: 0...10 V DC 24 V max, impedance: 30000 Ohm, resolution 10 bits
VIB configurable voltage: 0...10 V DC 24 V max, impedance: 30000 Ohm, resolution 10 bits
VIB configurable PTC probe: 0...6 probes, impedance: 1500 Ohm
VIA switch-configurable current: 0...20 mA, impedance: 250 Ohm, resolution 10 bits
Analogue output number
1
Asynchronous motor control profile
Voltage/frequency ratio - Energy Saving, quadratic U/f
Voltage/frequency ratio, 5 points
Voltage/frequency ratio, automatic IR compensation (U/f + automatic Uo)
Flux vector control without sensor, standard
Voltage/frequency ratio, 2 points
Discrete input logic
Positive logic (source) (F, R, RES), <= 5 V (state 0), >= 11 V (state 1)
Negative logic (sink) (F, R, RES), >= 16 V (state 0), <= 10 V (state 1)
output voltage
<= power supply voltage
width (w)
230 mm
Analogue output type
FM switch-configurable voltage 0...10 V DC, impedance: 7620 Ohm, resolution 10 bits
FM switch-configurable current 0...20 mA, impedance: 970 Ohm, resolution 10 bits
Discrete input type
F programmable 24 V DC, with level 1 PLC, impedance: 4700 Ohm
R programmable 24 V DC, with level 1 PLC, impedance: 4700 Ohm
RES programmable 24 V DC, with level 1 PLC, impedance: 4700 Ohm
isolation
Electrical between power and control
network frequency
47.5...63 Hz
supply voltage limits
323…528 V
switching frequency
6...16 kHz adjustable
12...16 kHz with derating factor
Local signalling
1 LED (red) for DC bus energized
motor slip compensation
Not available in voltage/frequency ratio motor control
Adjustable
Automatic whatever the load
Braking to standstill
By DC injection
Net weight
10.55 kg
physical interface
2-wire RS 485
Discrete output type
Configurable relay logic: (FLA, FLC) NO - 100000 cycles
Configurable relay logic: (FLB, FLC) NC - 100000 cycles
Configurable relay logic: (RY, RC) NO - 100000 cycles
Communication service
Time out setting from 0.1 to 100 s
Read holding registers (03) 2 words maximum
Read device identification (43)
Write multiple registers (16) 2 words maximum
Monitoring inhibitable
Write single register (06)
Operating position
Vertical +/- 10 degree
communication port protocol
METASYS N2
Modbus
LonWorks
APOGEE FLN
BACnet
Discrete output number
2
Motor power hp
4 hp
connector type
1 RJ45
1 open style
depth
208 mm
line current
6.2 A at 380 V
5 A at 480 V
continuous output current
7.2 A at 380 V
7.2 A at 460 V
maximum transient current
7.9 A for 60 s
Pollution degree
3 conforming to IEC 61800-5-1
electrical connection
VIA, VIB, FM, FLA, FLB, FLC, RY, RC, F, R, RES: terminal 2.5 mm² / AWG 14
L1/R, L2/S, L3/T: terminal 6 mm² / AWG 10
linearity error
VIA: +/- 0.15 % of maximum value for input
VIB: +/- 0.15 % of maximum value for input
FM: +/- 0.2 % for output
Network number of phases
3 phases
nominal switching frequency
12 kHz
dielectric strength
3535 V DC between earth and power terminals
5092 V DC between control and power terminals
Product destination
Asynchronous motors
speed range
1…10
Shock resistance
15 gn for 11 ms conforming to IEC 60068-2-27
Supply frequency
50...60 Hz - 5...5 %
torque accuracy
+/- 15 %
apparent power
5.5 kVA at 380 V
number of addresses
1…247
Supply
Internal supply for reference potentiometer (1 to 10 kOhm): 10.5 V DC +/- 5 %, <10 A, protection type: overload and short-circuit protection
Internal supply: 24 V DC (21…27 V), <200 A, protection type: overload and short-circuit protection
acceleration and deceleration ramps
Linear adjustable separately from 0.01 to 3200 s
Automatic based on the load
transient overtorque
120 % of nominal motor torque +/- 10 % for 60 s
Protection type
Overheating protection: drive
Thermal power stage: drive
Short-circuit between motor phases: drive
Input phase breaks: drive
Overcurrent between output phases and earth: drive
Overvoltages on the DC bus: drive
Break on the control circuit: drive
Against exceeding limit speed: drive
Line supply overvoltage and undervoltage: drive
Line supply undervoltage: drive
Against input phase loss: drive
Thermal protection: motor
Motor phase break: motor
With PTC probes: motor
Option card
Communication card for LonWorks
Transmission rate
9600 bps or 19200 bps
frequency resolution
Display unit: 0.1 Hz
Analog input: 0.024/50 Hz
Prospective line isc
5 kA
transmission frame
RTU
Sampling duration
2 ms +/- 0.5 ms F discrete
2 ms +/- 0.5 ms R discrete
2 ms +/- 0.5 ms RES discrete
3.5 ms +/- 0.5 ms VIA analog
22 ms +/- 0.5 ms VIB analog
Speed drive output frequency
0.5…200 Hz
Type of polarization
No impedance
Type of cable
Without mounting kit: 1 wire(s)IEC cable at 45 °C, copper 90 °C / XLPE/EPR
Without mounting kit: 1 wire(s)IEC cable at 45 °C, copper 70 °C / PVC
With UL Type 1 kit: 3 wire(s)UL 508 cable at 40 °C, copper 75 °C / PVC